Product

 Standard products

You are here: Home - Product List Product List
Shale Shaker Screen >> Features

Hook Strip Flat Shale Shaker Screen Features

 

- Different layers with different density. To arrange these layers reasonably and exactly, the screening effect will become better. Screen with different mesh number with suitable opening sizes of the backing plate. Doing so, our products will obtain the largest effective area under the condition of enough strength.

- High Strength and Long useful life. The bottom layer with low mesh number has coarse wire and can be tight bonded to the backing to make up one block, so increased the strength of whole screen mesh and the useful life.

- Cut down the stop time and reduce the cost. The mesh was divided to many independent small units by grids of the backing plate, can prevent rigs of tears from spreading overmuch. Accessory prepared rubber stoppers can be used to repair damages. By doing so, the operator can cut down the stop time and reduce the cost.

- Reinforced steel frame design:

1> Provide improved energy transfer from the shaker basket to the screen, so make solids separation faster.

2> Prolong screen’s life, thereby saving replacement cost and minimize the downtime.

3> No need for any crown rubbers, so saving the cost of replacements.

 - Unique seals of the screen perimeter can avoid any leakages.

- Patented pin-and-hole screen securing system. Guarantees that screens fit to the shaker basket snugly and will not slide when secured

 

 


 

 

Hook Strip Soft Shale Shaker Screen Features  

 

- More effective filtering area Hook strip soft screen is mounted on suitable shaker y hook strip. Because it has no metal backing plate, it has more effective surface.

- Long life time

1> The bottom thick wire cloth, it is not only help the above screen cloth get better filter, also support it, save the screen lifetime.

2> The plastic mesh layer can hold the two layer wire mesh together, and reduce the impact of the fluids, extend screen life. 

- Lighter Weight  Compared to the shaker screen mesh with metal plate back, the composite material has lighter weight.

- Repaired Easily  Due to the patented plug-repair system, the time for repairing the damaged screen is reduced largely and it only needs less than two minutes. When repairing the damaged screen mesh, there is no need to remove the damaged mesh as well as the processes of cutting, gluing and bonding the mesh, only with a special plug can solve the problem of repairing the damaged mesh.

 

 


 

 

Wave Shape Shale Shaker Screen Features

  

- Different layers with different density. To arrange these layers reasonably and exactly, the screening effect will become more and better.

- The waved cloth bonded to metal backing plate, has more surface. The effective area of a screen obtain 120% to 150% of a flat screen so that screen can load more drilling fluid flow.

- Screen Finer Faster  Utilizing Wave Shape Shale Shaker Screen enables rigs to screen 2 to 3 mesh sizes finer than with traditional flat panel screens without sacrificing capacity. This maximizes solids removal capabilities.

- Makes Fine Separations Wave Shape Shale Shaker Screens are capable of making separations as fine as 43 microns.

- Fits Existing Shakes There is no need to modify or replace existing equipment. Pyramid Shale Shaker Screens fit all shakers, allowing the most efficient use of existing equipment.

- Drier Cuttings  Wave Shape Shale Shaker Screens minimize fluid loss by spreading thinner layers of fluid over a relatively larger screen surface, offering more effective drying results.

- Enhanced Permeability  Gravity and vibration forces the solids into the corrugated screen’s troughs, thus allowing more fluid to pass through the top of the screen.

 

 


 

 

Steel Frame Shale Shaker Screen Features

 

- Different layers with different density. The screening effect will become better by arranging these layers reasonably and exactly.

- Reliable combination of the high strength frame, multi-ribs and the mesh cloth with moderate tension With reliable combination which can increase screen’s acceptably flow, the intensity and the lifetime.

- The wedge-shaped fastening device: it can make the screen erection more handily and quickly, save time, and reduce cost.

- Divided the whole mesh into several independent areas This can prevent rips from spreading overmuch, and prevent the part excessive expansion damaged.

- Accessory prepared rubber stoppers can be used to repair damages The operator can cut down the stop-time and reduce the cost.

 

 

 

 

Copyright @ 2012- 2015 Anping Qinghe Metal Mesh Co., Ltd All Rights Reserved  

Sitemap - Contact